Icom IC-7400 lähetyksen loppuminen = ei lähetä.
Ongelma näyttää olevan vanhemmissa versioissa, ja ne on korjattu uudemmissa malleissa. Myös vanhat mallit voi korjata.
Alla lisää juttua.
Icom IC-746 PRO (IC 746 PRO IC746PRO)
Transmit Problem
A significant number of hams have reported failures of IC-746Pro
Transmit functions within a few hours to a few months of
otherwise satisfactory operation. The remaining receive and menu
functions are normal, but TX is dead on all bands, HF, 6M and 2M.
Several hams(see eham.net product reviews) report multiple TX
failures, with the rigs going back to Icom in Washington state
more than once.
Indications are that:
IC151 on the RF Unit; and
D24 and Q25 on the CTRL unit are all bad.
These three components are all tied to the ANT jack(s) via the
HRX line, between the RF Unit and the CTRL Unit. The problem is
ESD (Electro-Static Discharge) related, and results from a
discharge to the ANT connector that will damage these components
even when the radio is powered OFF. The source of the ESD could
be applied when you change antennas, and might take a step with
the cable in hand to connect to a bandswitch or the amplifier,
etc...or picked up on the antenna as an environmental
electro-static charge, common especially during the dry winter
months (especially the winter of 2002-2003). NOTE: THERE IS NO
ESD PROTECTION on the HRX line.
I wrote to Icom Japan regarding this problem, and it is my
understanding that there has since been an "internal"
memo referred to as Internal Service Note #920 to addresses this
issue.
In the memo, a pair of 1SV252 PIN Attenuator Switch Diodes are
placed back-to-back on the HRX line to prevent ESD from damaging
the aforementioned components. The diodes are mounted on the RF
Unit at the junction of R1 and J1 (HRX) to GND.
These are very small, surface mounted components, so be
forewarned that unless you are trained and equipped to mount
these in an ESD safe environment, with proper surface mounting
equipment, eye magnification, etc (i.e., no coffee w/in 24-hrs),
then you are better off sending the rig to Icom and waiting for
them to install the ESD fix.
The parts are available from Icom Parts for $1.34ea, Part No.
91213606, PIN Diode 1SV252, Qty 2 required.
The diodes are packaged as a 3-terminal device, two diodes in
series, with the common junction (cathode-anode) not used. One
package is connected with Cathode to HRX, Anode to GND; and the
other Anode to HRX, Cathode to GND.
While you're attending to this fix, see my IC-746Pro SSB Monitor
Level fix, also found on this site.
*********** H U O M ***********
Allaolevia ohjeita on syytä noudattaa
jos rigi on vanhempaa versiota, ja ne ovat kyllä hyvät ohjeet
yleensäkin kaikille rigien käyttäjille.
1. Kun radio ei ole päällä, irrota antennikaapeli rigistä ja
maadoita kaapeli (myös kuumakarva) maadoituskiskoon.
Kytkiessäsi kaapelia takaisin rigiin kosketa toisella
kädelläsi rigin takamaadoitukseen ja toisella kädellä
kaapelin kuumalla karvalla maadoituskiskoon tai rigin
maadoitukseen estääksesi staattisen sähkön pääsemistä
antennipistokkeen kautta rigin sisälle.
2. On myös tarpeen varmistaa aika-ajoin että SWR on tarpeeksi
matala.
3. Käytä transistoripuskuripiiriä jos lineaarivahvistimesi ei
ole Icomin.
4. Älä käytä sisäistä antenninviritintä jos käytät
ulkoista viritintä. Lineaarivahvistimen kanssa käytä ulkoista
viritintä vahvistimen perässä ja pidä sisäinen viritin pois
päältä.
5. Jos käytät useita rigejä tai antenneja samaan aikaan
(workit yhtä aikaa, kuuntelet ja lähetät), varmista, että
antennit ovat tarpeeksi kaukana toisistaan, ettei RF pääse
rigin etuasteeseen ja tuhoa sitä.
6. Pidä kaikki kaapelit mahdollisimman lyhyinä, näin varsinkin
jos käytät lineaarivahvistinta. Suojaa kaapelit jotka ovat
liian pitkiä, ja maadoita suoja molemmista päistä estääksesi
takaisinpäin tulevaa RF:ää. Ferriitti "helmet" (tai
RF choke) kaapelin ympärillä voi auttaa, jos et pysty
suojaamaan kaapeleita.
7. Jos antennit ovat lähekkäin kytke käyttämätön antenni
maadoitukseen ja kytke vain yksi antenni kerrallaan rigiin. Tai
käytä sellaista antenninvalinta kytkintä joka maadoittaa
"kuuman karvan" niistä antenneista jotka ei ole
käytössä.
Alla 2 erillaista RF-Chokea
http://rudius.net/oz2m/ic746pro/index.htm
http://rudius.net/oz2m/ic746pro/ve3cg.htm
http://www.ham.dmz.ro/icom/ic-746pro-transmit-problem.php
http://www.n1eq.com/tech/page_01.html
http://www.qsl.net/k5lxp/projects/746Pro/746ProNoTX.html
http://www.qsl.net/kb9sss/IC746-faq.txt FAQ: Icom IC-746 HF/VHF Transceiver